Cable Fault Meter

A cable fault meter can locate open power cables, either live or dead (without current), with voltages up to 300 V. A cable fault meter can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power from the cable which is being tested. Many cable fault meter devices can also locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy.

A cable fault meter provides a safe way to test wall sockets when you are not sure about the cables within and their output. A cable fault meter is also very useful, as it allows for quick and safe checks before drilling holes in walls, ceilings and floors, so that workers do not accidentally electrocute themselves.

Catalog

Cable fault meter catalog

If you have any questions, please contact us at or +1 (561) 320-9162.

Cable Fault Meter PCE-186 CB

US$ 66.00

ex. VAT, ex. delivery costs

The cable fault meter PCE-186 CB consists of a transmitter and a receiver. The transmitter of the cable fault meter has many functions. For example, the cable fault meter can be used to find wires in walls or break cables.

- Voltage measurement AC / DC
- For detection of line interruptions
- Cable tracking in walls and cable duct
- Different beeps
- Resistance measurement

Cable Fault Meter PCE-160 CB

US$ 100.00

ex. VAT, ex. delivery costs

The PCE-160 CT cable fault meter is a line locator for hard-to-reach cables and is used, for example, in the automotive sector. In addition to the line location, there is also the continuity test with the cable fault meter.

Sensitivity adjustment
Headphone jack
Different beeps
Cable tracking in walls and cable channels
For mobile use

Cable Fault Meter PCE-LT 12

US$ 130.00

ex. VAT, ex. delivery costs

The cable fault meter is a versatile measuring instrument. In addition to the standard voltage and current measurements, the cable fault meter also has a network analysis. With this network analysis, the cable fault meter can be used to check, for example, LAN connections for their correct wiring and function.

Measurement function:

AC voltage
DC voltage
AC
DC
Resistance
Diode measurement
Continuity test

Cable Fault Meter PCE-180 CBN

US$ 178.00

ex. VAT, ex. delivery costs

PCE-180 CBN is a handheld, portable, battery-powered wire tracer or cable locator that consists of an amplifier probe and acoustic signal or tone generator. This locating device is designed to detect wires or cables hidden behind walls or insulation.

Uses an acoustic signal to detect wires and cables, including network and coaxial cables
Features a 3-position toggle switch (and 3-color LED) for line polarity, continuity and voltage testing
Comes with red and black test leads with alligator clips

Cable Fault Meter PCE-CLT 10

US$ 231.00

ex. VAT, ex. delivery costs

The cable fault meter PCE-CLT 10 is a multifunctional device which enables high accuracy and fast measurement results. If used appropriately, the cable fault meter can be used to measure cables that have already been installed and are still to be installed.

- Measuring range cable length: 5 ... 3000 m / 16.4 ... 9842.5 ft
- Measurement Units: m, ft
- Resolution: 0.1 m / 0.3 ft
- Measuring principle: time domain reflectometer
- 20 pre-set cable types

Cable Fault Meter PCE-CLT 20

US$ 244.00

ex. VAT, ex. delivery costs

The cable fault meter represents a powerful and versatile measuring instrument specifically designed for the precise measurement of electrical cables and conductors. With an impressive measurement range from 0.1 meters to an astonishing 30 kilometers, this device can measure and display cable lengths. Since the cable fault meter determines length based on conductor resistance, it can also measure resistance from 0.1 mΩ to 1999.9 Ω.

Cable Length: 0.1 m … 30 km
Standard Cable Types: Selectable from 0.15 … 240 mm²
Units in meters, kilometers, and feet
8 memory slots for custom cable types

Copper and aluminum cables
Resistance: 0.1 mΩ … 1999.9 Ω

Cable Fault Meter PCE-CL 20

US$ 396.00

ex. VAT, ex. delivery costs

The PCE-CL 20 is a cable fault meter or locator used to detect live and voltage-free electrical wires. This cable fault meter also can be used to locate metallic and non-metallic gas or water pipes, identify short circuits, and follow lines inside walls or under flooring.

Output signal: 125 kHz
Compatible with one- or two-pole circuits
Automatic, manual and UAC measuring modes

Cable Fault Meter PCE-CLT 20-ICA incl. ISO calibration certificate

US$ 469.00

ex. VAT, ex. delivery costs

Cable Length: 0.1 m … 30 km
Standard Cable Types: Selectable from 0.15 … 240 mm²
Units in meters, kilometers, and feet
8 memory slots for custom cable types

Copper and aluminum cables
Resistance: 0.1 mΩ … 1999.9 Ω
incl. ISO calibration certificate