Voltmeter (DMM)

Here you will find a voltmeter for measuring electrical magnitude in different fields of electronics.. Every voltmeter has a large, clear displayand fits in the palm of the hand, making it easy to handle. The voltmeter is used, above all, in professional training, in education, the industrial sector and in workshops. It is invaluable to professionals due to its high level of accuracy.

Here you will find all types of voltmeter for taking measurements of low to high voltages. We offer a voltmeter that has manual or automatic range selection and with or without an RS-232 interface for transferring data to a computer.

The corresponding test cables of the voltmeter come with the device as well as batteries so that it is ready to use straight out of the box. The voltmeter can be accompanied by an ISO calibration certificate either when it is ordered or included as part of an annual recalibration. This allows the voltmeter to be integrated into the group of internal testing tools of a company.

If you have any questions, please contact us at or +44 ( 0 ) 161 464902 0.

Voltmeter PCE-ITM 20

£ 343.00

Price excl. VAT &. delivery

This Voltmeter PCE-ITM 20 combines a versatile multimeter with an insulation tester. In addition to the usual measured quantities such as voltage, current and resistance, this Voltmeter PCE-ITM 20 is also equipped with a frequency and capacitance measurement.

Automatic range selection
Capacitancemeasurement
Integrated isolation tester
Internal memory
To IEC 1010, CAT III 1000V, CAT IV 600V
Frequency measurement

Voltmeter PCE-LCT 1-ICA incl. ISO Calibration Certificate

£ 279.00

Price excl. VAT &. delivery

With the Voltmeter, it is possible to measure leakage currents in the range of up to 100A. Leakage occurs when a current flows through an electrical conductor that is not normally designed to conduct electricity. The Voltmeter captures these currents and displays them on the display.

Measurable electrical parameters: AC V, AC A, resistance
Clamp diameter: 30 mm
Operating temperature: -10 … 50°C / 50 … 122°F
Current consumption: 10-mA
Incl. ISO calibration certificate

Voltmeter PCE-CBA 10

£ 22.00

Price excl. VAT &. delivery

The voltmeter PCE-CBA 10 can be used as a car battery tester. To test the battery, the voltmeter can measure, inter alia, the starting current to determine the capacity of the car battery in the range between 30 and 100 Ah.

For 12V starter batteries
Cold start current CCA: 100 … 1700 A
Battery capacity: 30 Ah … 100 Ah
Battery standards: DIN, JIS, EN, IEC, SAE, GB & MCA

Voltmeter PCE-PI 10

£ 27.00

Price excl. VAT &. delivery

The voltmeter is used to determine the direction of rotation of 3-phase voltage networks. Furthermore, the voltmeter is able to measure voltages up to 600V AC / DC. The rotating field direction is important for machines and plants.

Measuring range: 75 … 600V AC
3-phase rotating field detection
AC / DC voltage measurement
CAT III 600V

Voltmeter PCE-DM 3

£ 39.00

Price excl. VAT &. delivery

The Voltmeter is a practical and versatile meter that can be used in many areas such as electronics, electrical engineering and DIY. The Voltmeter enables the measurement of direct and alternating voltage, current, resistance, capacitance, frequency and temperature. With True RMS technology, it can also accurately measure complex AC voltages.

DC voltage: 0 ... 1000 V
AC voltage: 0 ... 1000 V
resistance: 0 Ω ... 100 mΩ
capacitance: 0 nF ... 10 mF
frequency: 0 Hz ... 1,000 kHz
temperature sensor: -20 ... +1000 °C
continuity test, diode test
non-contact voltage detection

Voltmeter PCE-DM 6

£ 40.00

Price excl. VAT &. delivery

Thanks to its handy design, the smart TRMS Voltmeter fits in any pocket like a smartphone and yet is equipped with many advantageous features. It is a versatile meter for DC and AC voltage, resistance, capacitance and frequency measurements. The Voltmeter offers additional functions such as diode test, a hold function and live test.
Measurement parameters:

DC voltage: 0 ... 1000 V
AC voltage: 0 ... 750 V
resistance: 0 ... 60 MΩ
capacitance: 0 ... 60 mF
frequency: 0 ... 10 MHz
safety standard: CAT III 600 V
non-contact voltage detection

Voltmeter PCE-DM 8

£ 44.00

Price excl. VAT &. delivery

The Voltmeter is a versatile meter that is used in many areas of electrical engineering and electronics. In addition to the basic measuring functions, the Voltmeter offers additional functions such as diode test, hold function, live test and continuity test and is equipped with a non-contact voltage detection (NCV) function.

direct voltage: 0 ... 999.9 V
alternating voltage: 0 ... 750 V
resistance: 0 Ω ... 99.99 MΩ
capacitance: 0 nF ... 99.99 mF
frequency: 0 Hz ... 9.999 MHz
temperature sensor: -55 ... +1300 °C
non-contact voltage detection
3 display modes

Voltmeter PCE-DM 7

£ 45.00

Price excl. VAT &. delivery

Our Voltmeter enables precise and reliable measurements in various electrical and electronic applications. The Voltmeter offers exact results for complex AC signals thanks to its true RMS function.
Measurement parameters:

DC voltage: 0 ... 999.9 V
AC voltage: 0 ... 750 V
alternating current: 0 ... 9.999 µA
direct current: 0 ... 9.999 A
frequency: 0 ... 5 MHz
resistance: 0 ... 99.99 Ω
capacitance: 0 ... 9.999 nF
temperature: -20 ... +1000 °C
non-contact voltage detection
bar graph

Voltmeter PCE-LT 12

£ 53.00

Price excl. VAT &. delivery

The voltmeter is a versatile measuring instrument. In addition to the standard voltage and current measurements, the voltmeter also has a network analysis. With this network analysis, the voltmeter can be used to check, for example, LAN connections for their correct wiring and function.

Measurement function:

AC voltage
DC voltage
AC
DC
Resistance
Diode measurement
Continuity test

Voltmeter PCE-CM 6

£ 58.00

Price excl. VAT &. delivery

The Voltmeter is a multifunctional meter for the precise measurement of alternating and direct voltage as well as alternating current that can be measured without direct contact to the line. The Voltmeter is suitable for measuring resistance, temperature, diodes, continuity, frequencies and capacitance and is particularly useful for diagnosing electrical and electronic components.

direct voltage: 0.1 mV ... 1000 V
alternating voltage: 0.1 mV ... 750 V
alternating current: 0.1 ... 1000 A
resistance: 0.1 Ω ... 60 MΩ
capacitance: 1 nF ... 100 mF
frequency: 0 Hz ... 10 MHz
temperature sensor: -20 ... +1000 °C
non-contact voltage detection (NCV)
automatic and manual measurement range selection

Clamp Voltmeter PCE-OC 5

£ 62.00

Price excl. VAT &. delivery

The Clamp Voltmeter is suitable for service technicians, stationary use in repair departments in specialist shops and in laboratories. The Clamp Voltmeter is designed for current measurements up to 400 A AC.

Graphic display of the measurement signal
Oscilloscope mode
memory function
Measurement parameters:
DC voltage
AC voltage
AC
frequency
resistance
capacity
temperature

Voltmeter PCE-LT 15

£ 62.00

Price excl. VAT &. delivery

The voltmeter PCE-LT 15 is a combination device which detects configuration errors in the network and can be used as a voltmeter at the same time. Thus, the periphery of a network can be quickly checked with the LAN tester.

Measuring function:

AC voltage: 750V
DC voltage: 1000V
Resistance: 4 MΩ
Continuity test: 400 Ω
Electrical safety: CAT III 600V

Voltmeter PCE-DC1

£ 68.00

Price excl. VAT &. delivery

Mini Voltmeter for measuring AC current, AC voltage, DC current and frequency.

AC current (50/60 Hz): 200 A / 0.1 A or 100 mA / ±3.0% + 8 digits
DC current: 200 A / 0.1 A or 100 mA / ±2.8% + 8 digits
AC test voltage (without contact): 100 VAC to 600 VAC 50 / 60 Hz
Frequency: 40 to 50 Hz / 51 to 510 Hz/ 0.51 to 1 kHz

Voltmeter PCE-IRM 10

£ 70.00

Price excl. VAT &. delivery

The Voltmeter is a compact and easy-to-use device for testing the battery quality of various battery types such as lithium, alkaline and lead-acid batteries. The Voltmeter can automatically check the internal resistance and voltage at the same time, with the measurement results clearly shown on the 2.4-inch colour display.

DC voltage: 0 ... 100 V
resolution: 0.0001 V
accuracy: ±0.5 %
resistance: 0 mΩ ... 200 Ω
resolution: 0.01 mΩ
accuracy: ±0.5 %
connections: Kelvin clamps
adjustable limit values
internal memory

Voltmeter PCE-CM 7

£ 72.00

Price excl. VAT &. delivery

direct voltage: 0.1 mV ... 1000 V
alternating voltage: 0.1 mV ... 750 V
direct current: 0.1 A ... 1000 A
alternating current: 0.1 ... 1000 A
resistance: 0.1 Ω ... 60 MΩ
capacitance: 1 nF ... 100 mF
frequency: 0 Hz ... 10 MHz
temperature sensor: -20 ... +1000 °C
non-contact voltage detection (NCV)
automatic and manual measurement range selection

Voltmeter PCE-CBA 20

£ 73.00

Price excl. VAT &. delivery

The Voltmeter tests 12V and 24V starter batteries. The voltmeter checks the condition of the car battery via the battery voltage in the charging cycle, when starting or when idling.

Measurement object: 12V / 24V starter batteries
Battery standards: DIN, JIS, EN, SAE
Power supply: 9 … 35V DC via test voltage

Voltmeter PCE-OC 15

£ 85.00

Price excl. VAT &. delivery

The Voltmeter is a versatile and universally applicable meter that combines the functions of an Voltmeter and a true RMS multimeter. Our Voltmeter was developed for practical and mobile use and is ideal for troubleshooting thanks to its extensive features.
Measurement parameters:

Voltmeter mode
DC voltage: 0 ... 999.9 V
AC voltage: 0 ... 750 V
direct current: 0 ... 10 A
alternating current 0 ... 10 A
frequency: 40 Hz ... 1 kHz
resistance: 0 ... 99.99 MΩ
capacitance: 0 ... 99.99 mF
temperature: -20 ... +1000 °C
graphical display of the measured value

Voltmeter PCE-OC 50

£ 89.00

Price excl. VAT &. delivery

This innovative 3-in-1 Voltmeter is the perfect combination of a powerful Voltmeter , a versatile multimeter and a signal generator. It has been specially developed for electronics technicians, engineers and hobby users who are looking for a compact, versatile and user-friendly device to carry out their measurement tasks efficiently.
Multimeter functions:

2-channel Voltmeter
bandwidth: 10 MHz, sampling rate: 50 MS/s
voltage: 0 ... 1000 V DC, 0 ... 750 V AC
current: 0 ... 9.999 A AC/DC
resistance, capacitance, temperature
non-contact voltage detection
signal generator: 1 Hz ... 2 MHz

Purchase Advice on Voltage Measuring Devices

A voltmeter is used to measure the DC or AC voltage. PCE Instruments offers a wide range of different measuring instruments for carrying out such tasks.
Basically, the voltage measuring devices may be differentiated as follows: measuring devices that can only perform the voltage measurement or also some that possess other measuring functions, such as current measurement, resistance measurement, diode test, etc. In this case, one speaks not just about a voltage tester but rather about a multimeter. In principle, however, every multimeter is also a voltage measuring device.
This purchase advice shows the basic differences between the voltage measuring devices from our assortment.

The simplest type of voltage measuring device is the two-pole voltage tester. This voltmeter gauge usually consists of two parts, which are held in the left or right hand. On the front part of the voltmeter there are measuring tips needed to measure voltage. This type of the voltage measuring instruments is often used in the trade and in maintenance. The simple design provides a comfortable and fast working with this voltmeter. Frequently, these voltmeters also have a test button for fault current protection facilities.

Another form of voltage measuring devices is a multimeter. In addition to the voltage measuring function, further measurement options are available here, such as current measurement, resistance measurement, capacitance test, diode test, etc. Voltage measuring instruments, which are designed as multimeters, are structurally completely different from a two-pole voltage tester. Here, the test leads are not connected to the voltmeters directly, but changeably attached to the multimeter. Thus, for example, the voltage gauges can be placed on a workbench and the measurement values can be conveniently read, even if an access to the voltage measurement is difficult.

In addition to the multimeters, current clamps can also be used as a voltage measuring device. A basic requirement here is that the current clamp has separate measuring inputs for voltage. When the current clamp is used as a voltage measuring device, it is often the case, that also the measuring functions, such as continuity test, etc. are integrated in the voltmeter.

Should you have further questions about our voltage measuring devices, do not hesitate to contact us.