Electrical Tester

The PCE-360 is a Single-Phase Power Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.

• Measuring range: 10 … 999.9 V
• AC voltage AC
• Alternating current AC
• Active power
• Power factor
• Phase angle
• Frequency
• Harmonic measurement
• Data memory: 512 kB   (non-volatile memory)
• incl. 4 current clamps / tapping terminals
• Standards: IP 30 / IEC 61 010, 600 V / CAT III
• incl. ISO Calibration Certificate

The Electrical Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This 3-Phase Electrical Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

• PCE-830 + PCE-6801 amp clamp (100 A)
• Electrical conductor pick-up: 30 mm diameter
• Range selection: manual (1 A, 10 A, 100 A)
• Clamp dimensions: 210 x 62 x 36 mm
• Incl. ISO calibration certificate

The Electrical Tester is used for measuring one to three phases of electrical quantities for alternating current (AC). This Electrical Tester also measures such parameters as voltage, current, frequency, harmonics and power as well as indicating, according to standard EN50160, harmonic values, interharmonics and asymmetrics. Interference, such as interruptions, leaks, overloads or transience (from 16µs) are detected with their corresponding values.

• PCE-830 + PCE-6802 amp clamp (1000 A)
• Electrical conductor pick-up: 55 mm / 2.2 in diameter
• Range selection: manual (10 A, 100 A, 1000 A)
• Clamp dimensions: 244 x 97 x 46 mm / 9.6 x 3.8 x 1.8 in
• Incl. ISO calibration certificate

Three-Phase Electrical Tester with network analyzer / power and energy meter with data logger.

• Real-time test, register and measurement of voltage and current (real and effective) 
• Measures power factor and phase angle, frequency, energy, active, reactive and apparent power   (single-phase or three-phase in symmetrical networks). 
• Max. conductor diameter: 55 mm / 2.2 in
• Records up to 50,000 records

This three-phase electrical tester is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The three-phase electrical tester is equipped with data logger. The test instrument is delivered manufacturer calibrated (ISO or certification as an option).

• Real-time test, register and measurement of voltage and current (real and effective) 
• Measures power factor and phase angle, frequency, energy, active, reactive and apparent power   (single-phase or three-phase in symmetrical networks). 
• Max. conductor diameter: 55 mm / 2.2 in
• Datalogger for 50,000 readings / software/ USB interface 
• incl. ISO Calibration Certificate

The PCE-360 is a HVAC Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.

• Measuring range: 10 … 999.9 V
• AC voltage AC
• Alternating current AC
• Active power
• Power factor
• Phase angle
• Frequency
• Harmonic measurement
• Data memory: 512 kB   (non-volatile memory)
• incl. 4 current clamps / tapping terminals
• Standards: IP 30 / IEC 61 010, 600 V / CAT III
• incl. ISO Calibration Certificate

• For 12V starter batteries
• Cold start current CCA:  100 … 1700 A
• Battery capacity:  30 Ah … 100 Ah
• Battery standards:  DIN, JIS, EN, IEC, SAE, GB & MCA

The Electrical Tester has been designed to detect, indirectly, AC/DC current and frequency. The Electrical Tester has a flashlight integrated to allow for the point of measurement to be illuminated, and a function to test the voltage without contact.

• AC current (50/60 Hz): 200 A / 0.1 A or 100-mA / ±3.0% + 8 digits
• DC current: 200 A / 0.1 A or 100-mA / ±2.8% + 8 digits
• AC test voltage (without contact):100 VAC to 600 VAC 50 / 60 Hz
• Frequency (3 ranges): 40 to 50 Hz / 51 to 510 Hz/ 0.51 to 1 kHz

Digital Clamp Meter for measuring AC/DC current, AC voltage and resistance. This clamp meter is designed to indirectly detect AC/DC current and ohms. The clamp has white LEDs which illuminate the point of measurement and test the voltage without contact. Small dimensions of this device allow to take measurements in places with limited access. The clamp meter comes manufacturer calibrated and can optionally be certified according to ISO or standards.

• AC / DC current, voltage and resistance measurement
• 3 2/3-digit LCD display
• Power supply: 2 x 1.5V AAA battery
• Dimensions: 164 x 65 x 32 mm / 6.4 x 2.5 x 1.2 in

This electrical tester was developed for the indirect measurement of AC/DC currents as well as the frequency. A non-contact voltage tester function and a torch/flashlight for illuminating the measuring point have also been integrated into this electrical tester.

• AC/DC current, AC voltage and frequency measurement
• AC voltage test (contactless test):   100 VAC to 600 VAC 50/60Hz 100 VAC to 600 VAC 50/60Hz
• DCA zero point function

• insulation resistance: 1 MΩ ... 200 GΩ
• resolution: 0.01 MΩ
• accuracy: ±(5 % of Rd. +10 digits)
• test voltages: 250 ... 2500 V
• voltage measurement: 10 ... 600 V
• resolution: 1 V
• accuracy: +(0.8 % of Rd. +5 digits)