Measuring Instruments

The large display is a measuring device for stationary measurement of relative humidity and temperature. This large display consists of an LED seven-segment display with a digit height of 100 mm, which enables you to read it very well even at a distance of up to 50 m.

• Temperature measuring range: 0 … +60 °C (Celsius only)
• Humidity measuring range: 10 … 95 % RH
• Up to 50 m (164 ft) reading distance
• External sensor (wired)
• Voltage supply: 230 V AC
• with analogue output 4 … 20 mA

The Xgard-1-CL2 is a single-gas sas detector used to warn for gases (Chlorine, CL₂, 0 … 5 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

• Stationary
• For (Chlorine, CL₂, 0 … 5 ppm)
• Additional display and alarm station
• ATEX or UL approval

The Xgard-1-SO2 is a single-gas Gassensor used to warn for gases (Sulfur Dioxide, SO₂, 0 … 10 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

• Stationary
• For (Sulfur Dioxide, SO₂, 0 … 10 ppm)
• Additional display and alarm station
• ATEX or UL approval

This Formaldehyde Meter HFX205-100 is designed to detect formaldehyde in air. The Formaldehyde Meter HFX205-100 shows the formaldehyde-concentration on site and thereby avoids time-consuming and expensive analysis in laboratories. The Formaldehyde Meter HFX205-100 runs with help of an electromechanical sensor and is designed to determine the current permitted limit. A measurement can be accomplished in less than 30 seconds.

• Range Formaldehyde: 0…100 ppm
• Short reaction time
• Real-time display
• Manual and auto data storage
• High-speed USB
• Software for Online Data transfer

The Xgard-1-NO2 is a single-gas gas sensor used to warn for gases (Nitrogen dioxide, NO₂, 0 … 10 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

• Stationary
• For (Nitrogen dioxide, NO₂, 0 … 10 ppm)
• Additional display and alarm station
• ATEX or UL approval

Single-Gas Gas Detector warning for gases (for Carbon Dioxide CO₂), / without display / with signal output for sensors in combination with a stationary equipment to detect gases (with ATEX approval).

• Stationary
• For Carbon Dioxide CO₂
• Additional display and alarm station
• ATEX approved

TETRA-MINI alerts the user acoustically, visually and vibrationally to the presence of flammable gases (CH4), oxygen (O2), hydrogen sulfide (H2S) and carbon monoxide (CO). Furthermore, this unpumped four-gas meter displays the current measured value on its graphic LCD screen with backlight. Other gas sensors are available for this instrument. Call for details.

• Sensor types: CH4 / H2S / CO / O2
• Easy one-button operation
• Rechargeable Li-ion battery
• ATEX II 2G EEx iad IIC T4 approved

The Xgard-1-NH3 is a single-gas Gas detector used to warn for gases (Ammonia, NH₃, 0 … 50 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

• Stationary
• For (Ammonia, NH₃, 0 … 50 ppm)
• Additional display and alarm station
• ATEX or UL approval

The Xgard-1-O3 is a single-gas Gassensor used to warn for gases (Ozone, O₃, 0 … 1 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

• Stationary
• For (Ozone, O₃, 0 … 1 ppm)
• Additional display and alarm station
• ATEX or UL approval

A belt tension meter measures the belt tension of a belt when it is stationary. The maintenance kit includes a vibration accelerometer for checking vibrating parts, machines and systems. It is also possible to measure the surface speed with a tachometer up to 99,999 revolutions per minute.

Belt Tension Meter

• Measurement of the vibration frequency of the belt
• Measuring range: 10 … 900 Hz
• Accuracy: ± (1% of reading + 4 digits)Vibration Meter
• Acceleration: 0.0 … 399.9 m/s² / 0.0 - 15744 in/s²
• Velocity: 0.00 … 399.9 mm/s / 0.00 - 15.74 in/s
• Displacement: 0.000 … 3.9 mm / 0.000 - 0.154 inTachometer
• Contactless measurement: 5 … 99,999 rpm
• Contact measurement: 0.5 … 19,999 rpm
• Surface measurement: 0.05 … 1,999.9 m/min

The Xgard IR Gas Detector is a rugged, explosion-proof gas sensor for hydrocarbons or carbon dioxide. The Xgard IR gas detector is available in different versions, depending on which gases it is to be used for. The gas detector measures the respective gases using a dual wavelength infrared sensor.

• Various finishes available
• Explosion-proof construction with ATEX approval
• Infrared sensor
• 3-wire 4…20 mA output

The Xgard-1-H2 is a single-gas Gas detector used to warn for gases (Hydrogen, H₂, 0 … 2000 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

• Stationary
• For (Hydrogen, H₂, 0 … 2000 ppm)
• Additional display and alarm station
• ATEX or UL approval

The closing force transducer is an electronic closing force measuring device for externally powered doors and gates. Typical use is the final inspection of new systems as well as regular inspections.

• Measuring range: 0 … 2000 N
• Stiffness: 500 N/mm
• Accuracy: +/- 3N or 3% of reading
• Data logger unit with LCD display
• Professional, comprehensive PC software
• Memory for 100 measurements
• Standards – EN 12445/12453, EN 60335-2, DIN V 18650, ASR A1.7, etc.
• Incl. ISO calibration certificate

The Xgard-1-PH3 is a single-gas Gassensor used to warn for gases (Phosphine, PH₃, 0 … 1 ppm), with display and signal output for sensors in combination with a stationary instrument to detect gases (ATEX or UL approval).

• Stationary
• For (Phosphine, PH₃, 0 … 1 ppm)
• Additional display and alarm station
• ATEX or UL approval

The force gage PCE-DFG N 100K-ICA measures both tensile forces and compressive forces with a very high resolution and sampling rate. The force gage helps to determine the yield strengths, the tear-off force and is used wherever acting forces have to be documented.

• Measuring range: 0 … 100 kN / 100,000 N
• Resolution: 10 N
• Accuracy: ± 1% of the measuring range
• Memory for 100 measurements
• USB interface
• Graphic display
• Including ISO calibration certificate

The PCE-360 is a Single-Phase Power Meter with data logger functionality. This versatile power analyzer can take single-phase and three-phase power measurements both in real time and over an extended time period.

• Measuring range: 10 … 999.9 V
• AC voltage AC
• Alternating current AC
• Active power
• Power factor
• Phase angle
• Frequency
• Harmonic measurement
• Data memory: 512 kB   (non-volatile memory)
• incl. 4 current clamps / tapping terminals
• Standards: IP 30 / IEC 61 010, 600 V / CAT III
• incl. ISO Calibration Certificate

The main advantage of a steady-state stroboscope RT STROBE 5000 LED with intelligent LED-technology results from the absence of a short life xenon-tube, which is usually the first part which has to be replaced.

• Frequency range: 0…120,000 FPM
• Low-wear LED light trigger
• Illumination level 300 x 500 mm
• High intensity of light
• 120 LEDs